Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
Hire a Pest Control Company Now
How do you actually feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is conveniently accessible, the task can relocate speedily; if you need to open up a wall surface to get rid of the old bathtub and also position the brand-new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the task and are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new bathtub in your restroom if you have already bought a new tub and also do not require to transform the setup of your previous water system pipes.
Your tools and material checklist need to consist of the following:
Planning for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, position the bathtub in the required position. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Load the bath tub as well as additionally check the overflow outlet and the normal outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been utilized at least once as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, causing difficulties with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealant can fracture relatively very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader about Tools You Need to Install a New Bathtub , I figured sharing that excerpt was really useful. Loved our blog posting? Please share it. Let another person discover it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Start Now Report this page